Roof Advice/Metal Roofs

Metal Roofs

Metal Roof Re-Screws in Lennox Head: How to Tell If Your Roof Is Due

New Class 4 roof screws along the flashing of a corrugated metal roof in Lennox Head after a whole-roof re-screw

Most Colorbond and Zincalume roofs in Lennox Head are due for a whole-roof re-screw somewhere between 10 and 15 years old, and the beachfront ones sit at the early end of that. The sheets usually have decades left; it is the rubber washer under each screw head that salt air and UV wear out first, and once the washers go, wind-driven rain gets in. A whole-roof re-screw with Class 4 coastal screws starts from $2,000 and is the cheapest thing you can do to keep a metal roof watertight.

How long do roof screws last in Lennox Head?

It depends on which part of Lennox you live in, because the salt load is not the same across the suburb. On the beachfront along Seven Mile Beach and out toward Lennox Point, the roof takes salt spray off the break every day the wind blows, and it blows most days. Washers on those roofs are often brittle by 10 years. In the village and around Lake Ainsworth the air is a little kinder but far more humid, so screw heads stay damp overnight and rust halos appear around them before the washers have even failed. Up the hill on the western side of the Coast Road and toward Pat Morton Lookout, roofs are a few hundred metres further from the surf and get the benefit of rain washing them more evenly, so 12 to 15 years is more typical.

The reason for the short life is in the materials, not the workmanship. BlueScope's fastener bulletin puts a roof anywhere within about 400 metres of the ocean in the severe marine category, where a standard Class 3 screw should not be used at all. Practically every home in Lennox Head and Skennars Head sits inside that band. If your roof was built or last re-screwed with Class 3 fixings, which was common on homes finished before the coastal screw rules were widely followed, expect the screw heads themselves to rust out, not just the washers.

What's a 10-minute check you can do yourself?

You do not need to get on the roof, and on a coastal metal roof we would rather you did not. Three checks from the ground and the roof space tell you most of what you need to know.

From the street, in low morning sun or after rain, with binoculars if you have them:

  • Brown halos or streaks running downhill from screw heads, especially on the east and south-east faces.
  • Screw heads that look taller than their neighbours, which means they are backing out.
  • Sheets that lift or rattle along one edge in a stiff southerly.

In the roof space on a bright day, with the light off:

  • Pinpricks of daylight along the screw lines.
  • Tea-coloured water marks on the sarking or insulation directly under a row of fixings.
  • Rusty screw tips, or white powder around them, on the underside of the sheet.

The southerly test: if the ceiling only gets damp when rain comes in on a south-easterly and stays dry in still rain, water is being pushed uphill past failed washers. That pattern is the most common re-screw call-out we get in Lennox, and it rarely means the sheets are at fault. If you tick two or more of these, the roof is due for a proper look. Our guide to the seven signs a metal roof needs re-screwing goes through each one in more detail.

Why are the screws backing out of my metal roof?

A Colorbond sheet grows and shrinks a little every day as it heats up and cools down, and every one of those cycles tugs on the screws. On a new roof the rubber washer absorbs that movement. As the washer hardens and flattens, the screw loses its grip on the sheet, the hole in the batten slowly enlarges, and the screw starts to walk out. Over-driven screws make it worse: a screw that was sent in hard enough to dimple the sheet has already crushed its washer, so it fails years early.

A screw standing proud is not a one-off fault to be tapped back down. It is the roof telling you that every fixing of the same age is at the same stage. Re-driving it into the worn hole does nothing, because there is no fresh timber left for it to bite. The fix is a new screw, and where the hole has stripped, a longer or oversized screw that reaches sound timber. On a re-screw we check each hole as we go and step up to oversized fixings wherever the original has let go.

Why do we re-screw the whole roof and not one slope?

Every screw on your roof went in on the same day, from the same box, and has sat in the same salt air since. The ocean-facing slope shows it first, but the sheltered side is only a season or two behind, and the ridge, the sheet ends and the flashings carry the closest-spaced screws of all. Re-screwing one slope means setting up the roof access, the swarf cleaning and the safety gear twice, and it leaves you with a roof that is half watertight. That is why our re-screw is a whole-roof job with a written workmanship warranty across the lot, and why it comes with a dated photo report so you can see exactly what came out and what went in.

The honest exception: if your roof is young and a handful of screws have failed in one spot, usually around a penetration or where a tradie from another trade has been on the roof, that is a leak repair from $350, not a re-screw. We will tell you which one you need after we have walked the roof, and we will not sell you a whole-roof job on a roof that does not need one.

Which screws should go on a Lennox Head roof?

Class 4 screws rated to AS 3566, every time. Class 4 is the highest corrosion-resistance class in the standard, and BlueScope's selection guide calls for it on Colorbond in severe marine areas, which covers all of Lennox Head. The washer matters as much as the coating: Lysaght's fastener bulletin specifies EPDM washers rather than neoprene for marine exposure, because neoprene hardens and cracks sooner in salt and UV. We use colour-matched Class 4 heads so the roof does not end up speckled with silver dots from the street.

Two things a good re-screw also gets right. First, the driver: screws go in with a depth stop so the washer is compressed just enough to seal and no further. An impact driver on full setting is how a re-screw ends up leaking again in two or three years. Second, swarf: the steel filings from drilling are blown and swept off the roof before we leave, because each filing left behind rusts into the paint and looks like the sheet itself is failing. One thing to avoid is stainless screws on Colorbond, which BlueScope does not recommend because the two metals react against each other at the hole. And if your roof is a concealed-fix profile such as Klip-Lok, there are no screws through the sheet to replace; those roofs are checked at the clips and the sheet ends instead.

What does a re-screw cost in Lennox Head?

Prices below are from our Northern Rivers cost guide and are confirmed in writing after we have walked your roof.

Whole-roof Colorbond re-screw, Class 4 fixings
from $2,000
Leak repair where only a few screws or a flashing have failed
from $350
Standard roof report with photos
$249
Minimum call-out
$300

What moves the re-screw figure is roof size, pitch, whether it is single or two storey, access around the house and how many fixings need stepping up to oversized screws.

For context, an independent 2026 NSW cost guide puts a whole-roof re-screw at roughly $1,400 to $2,400 on a single-storey home and $2,200 to $3,200 on two storeys, with the north coast toward the top of that range and Class 4 coastal screws adding 15 to 25 per cent. Our from-$2,000 figure already includes the Class 4 screws, the swarf clean and the photo report, so compare quotes on the same basis: ask any roofer which screw class and which washer they are using, and whether every screw is being replaced or just the ones that look bad.

When is a re-screw not the answer?

A re-screw fixes fixings. It does not fix sheets that have rusted through at the laps, around the screw holes or along cut edges, and it does not fix a roof that is simply at the end of its life. If a screwdriver pressed on a rust patch from inside the roof space goes through, that sheet needs replacing, not a new screw. On the oldest beachfront roofs in Lennox, sheeted 25 to 30 years ago in a grade that was never right for the surf, the honest conversation is about sheet replacement or a re-roof, and we will give you that figure instead of re-screwing something that will not hold. Our guide to re-screwing or replacing an ageing Colorbond roof walks through that decision.

Surface rust and cut-edge rust on otherwise sound sheets are a different story: those are treated and coated as part of the job, or quoted as a rusty roof repair alongside the re-screw. Where the roof is sound but faded and chalky, a re-screw is also the first step before any roof restoration or painting, because paint over perished screws hides the problem while it keeps getting worse.

Booking a re-screw in Lennox Head

We are based in Lennox Head, so re-screws here are planned work we book around a dry forecast and usually fit between other local jobs. If the roof is leaking now, call 0412 483 911 and we aim to make-safe the same or next day, weather permitting, then quote the re-screw properly. If it is not leaking yet and you just want to know where you stand, a $249 roof report gives you dated photos of every fixing line, a plain-English verdict on whether the roof is due, and the fee is credited to any repairs booked within 30 days. You can book a report or request a quote through the site, or check the Lennox Head roof repairs page for what else we see on roofs around here.

Questions

Common questions

Once, at the mid-life point, which on the Lennox coast is usually 10 to 15 years after the roof went on, earlier on the beachfront. After a re-screw with Class 4 screws and EPDM washers you should not need another for a similar stretch. A yearly check for beachfront roofs, and every one to two years elsewhere in Lennox, catches the washers before they let water in.

Sources

Need this checked on your roof?

We're local to Lennox Head and cover the whole Northern Rivers. Every job is photo-documented and warranted.

  • metal roof re-screw Lennox Head
  • screws backing out of metal roof
  • Class 4 roof screws
  • Colorbond roof screws rusting
  • roof screw washers
  • metal roof repairs Lennox Head
  • Skennars Head roof repairs
  • re-screw cost Northern Rivers
CR

Coastal Roofing Repairs

Local Northern Rivers roofers · 28 years on the tools · insured

Written by the Coastal Roofing Repairs team, 28 years roofing on the NSW North Coast. We work on coastal metal and tile roofs every day — these guides come straight from what we see on the tools, not a marketing desk.